請選擇 進入手機版 | 繼續訪問電腦版

台灣無線電俱樂部 TAIWAN RADIO CLUB ( TRC )

 找回密碼
 註冊
搜索
台灣摩托羅拉授權代理商Belfone 台灣總代理anytone 自由通無線電對講機無線王資訊有限公司
樓主: whitemagic

車裝台安裝後天線駐波怎麼測都不對的案例

  [複製鏈接]
  • TA的每日心情
    奮鬥
    2012-3-25 15:59
  • 簽到天數: 28 天

    [LV.4]偶爾看看III

    發表於 2012-1-10 23:16:15 | 顯示全部樓層
    WSUgocouars 發表於 2012-1-10 22:29
    那我會留一隻我最喜歡的一隻當報酬.....  哇哈哈哈!~~~~~~

    回復 支持 反對

    使用道具 舉報

  • TA的每日心情
    開心
    3 天前
  • 簽到天數: 1941 天

    [LV.Master]伴壇終老

    發表於 2012-1-11 00:04:39 | 顯示全部樓層
    et006623 發表於 2012-1-10 23:16

    會怕了ㄏㄡ!~~~~ 免驚.... 反正都封印的, 拿來練功看看!~~~~~
    回復 支持 反對

    使用道具 舉報

  • TA的每日心情
    開心
    2012-2-26 18:12
  • 簽到天數: 20 天

    [LV.4]偶爾看看III

     樓主| 發表於 2012-1-11 08:21:11 | 顯示全部樓層
    關於天線的問題
    我在請教各位先進
    如果一支VHF天線我使用頻譜去測
    假設我監測的頻段是從140MHZ-170MHZ
    這支天線所能找到的某個頻率區域最佳駐波僅有1.5
    這天線不管怎麼剪
    是否都不可能會出現哪個頻率就能降低到1.2以下~~

    個人測試的天線經驗中
    多數的天線即使出廠的頻率不是很準
    但也僅是偏了
    至少他會有某個頻率的駐波測量是很優的
    這種天線經過裁剪
    也多能找到適用的頻率上

    但那種不管在哪個頻段駐波都差的
    最優的也僅有1.5
    這種天線是不是沒救的?
    回復 支持 反對

    使用道具 舉報

  • TA的每日心情
    開心
    3 天前
  • 簽到天數: 1941 天

    [LV.Master]伴壇終老

    發表於 2012-1-11 09:24:27 | 顯示全部樓層
    本帖最後由 WSUgocouars 於 2012-1-11 09:28 編輯
    whitemagic 發表於 2012-1-11 08:21
    關於天線的問題
    我在請教各位先進
    如果一支VHF天線我使用頻譜去測


    以我個人之前的修天線經驗....... 不一定都用修短的方式, 除了放開內六角螺絲把天線增長外, 我還會準備不銹鋼條來調..... 曾經有隻天線怎麼弄都下不到SWR 2 以下, 索性把原廠的上半截換成較長的, 看它最優的SWR落在那個頻率, 之後慢慢修短到我要的頻率. 記得增加快十公分長. SWR 在我要的頻率壓到 1.15.   

    另外我也發現在測量時真的要因地而異....  因為儀器蠻容易因旁邊的環境而產生不同的讀值...  因為SWR 就是跟反射波有關.....
    回復 支持 反對

    使用道具 舉報

  • TA的每日心情
    開心
    3 天前
  • 簽到天數: 1941 天

    [LV.Master]伴壇終老

    發表於 2012-1-11 09:31:59 | 顯示全部樓層
    本帖最後由 WSUgocouars 於 2012-1-11 10:27 編輯
    et006623 發表於 2012-1-10 06:41
    哈哈~
    一點都不意外哦~
    小弟在去年5月份開始重拾無線電不歸路時,


    你這兩隻用AW07A天線分析儀測時是在何種環境測呢?  有時會因旁邊的東西影響讀值喔!!~~~~  還有天線垂直與否,角度都也會影響 SWR 讀值耶!!!
    回復 支持 反對

    使用道具 舉報

  • TA的每日心情
    慵懶
    2013-12-29 10:03
  • 簽到天數: 64 天

    [LV.6]常住居民II

    發表於 2012-1-15 00:08:26 | 顯示全部樓層
    whitemagic 發表於 2012-1-9 23:44
    先說抱歉
    這篇沒有寫真可看
    文字敘述應該可讓大家暫時明瞭

    在您文中提到
    只要把天線直接種在儀表上的M母接頭上

    可見那位老友台應該也有些許的錯誤觀念吧

    車天線不需地網因此也稱NR天線,靠的就是以車體鈑件代替地網

    如果直接將天線安裝在天線分析儀上來測量......您覺得問題在哪裡呢?



    以上為個人心得,如有錯誤請指正
    回復 支持 反對

    使用道具 舉報

  • TA的每日心情
    開心
    3 天前
  • 簽到天數: 1941 天

    [LV.Master]伴壇終老

    發表於 2012-1-15 01:25:42 | 顯示全部樓層
    本帖最後由 WSUgocouars 於 2012-1-15 01:54 編輯
    阿鋒 發表於 2012-1-15 00:08
    在您文中提到
    只要把天線直接種在儀表上的M母接頭上


    其實擁有天線分析儀的人真的就懂得怎麼用嗎?  我看很多都是懂非懂.... "我就是其中一個".... 自從搬了那台 AEA VIA BRAVO 天線分析儀, 我才去 K它的一些應用文件.....  發現 SWR/RL 並不一定能看出天線的共振點...   我到今天才恍然大悟.....  共振不起來, 怎麼把電波射出去......OMG.......   


    From  http://www.aeatechnology.com/software/application-notes/an112
    Tuning an Antenna
    Written by Bill Ashley

    Abstract:
            This paper describes how to use an AEA Technology network analyzer to tune an antenna. This paper discusses tuning issues at a general level; no specific model of antenna is addressed here.
    Introduction:
            For best link efficiency, you must properly tune the antenna to resonance. Additionally, if the antenna has two or more adjustments available, you should also tune the antenna for the optimum match.
           Resonance occurs when the reactive portion of the antenna impedance is zero. (共振會在天線阻抗的電抗部份為零時發生). This causes the voltage to be in phase with the current, and allows the transmitter to generate its maximum power. (這會讓電壓和電流在同相位, 並會讓發射機產生最大的輸出功率).  SWR or return loss readings do not provide enough information to determine resonance. (駐波比 或 反射損失並不能提供足夠的資訊來推測共振) You must use a vector impedance reading to see resonance.  (你必須要有向量阻抗的讀值才可看它的共振)

            The transmission lines used to feed the antenna can add a layer of confusion to the measurements. 剛開始一起使用傳輸線量測時會多一層的混淆.   If practical, tune the antenna by itself first, then add in the feedline for more measurements. 在練習時, 應先單單測天線自己, 之後才加上線來增加不同量測.

    翻不下去了~~~~~~~~~~~~~~~`

    Discussion:

            Read the manufacturer’s instructions to find out about available tuning adjustments. Some common forms of adjustment include length (height) adjustment, feed element tap, variable caps or coils, or some balun adjustment. The mounting height combined with the mast and tower affect the tuning, so try to make the measurement under conditions that represent the actual installation. Always use the simplest set of adaptors required to make a measurement. If you are operating at high frequencies or at a very narrow bandwidth, you should cable null the analyzer (and adapters). See AN101 for info about cable nulling.

    Tune the antenna to resonance. Set one of the plots on the network analyzer to impedance angle (or reactance). Tune for zero reactance or impedance angle. If the combinations of adjustments are unable to do this, a tuning stub may be required. See AN110 for more information on stub tuning.
    Tune the antenna for best match, while maintaining resonance. Set the other plot of the network analyzer to Total Z. The best match occurs when the total Z approaches the characteristic impedance (Z0) of the system, usually 50 ohms. Multiple adjustments often interact, so a little patience goes a long way.
    Once you have achieved both resonance and match, save the reading to memory for saving to the PC later on. Many people want to see reports with the scalar values, i.e. SWR or return loss. You may extract this data from the vector data (Z and Z angle or Resistance and Reactance).
    Add the feed line to the antenna. Measure the input of the feedline; it should be close to a good match and near resonance. When the Z0 of the feedline does not match the antenna Z, the resonance information will be masked by the feedline length. This situation should be addressed with baluns or other matching networks. Ideally, you want the transmitter Z = feedline Z0 = Antenna Z.
    Conclusion:
            Use an AEA Technology network analyzer to tune your antenna for resonance and match. When you achieve both resonance and match, you have your best efficiency. SWR/return loss meters do not give resonance information.

    References:
    AN101    When to Use Cable Null, AEA Technology
    AN110    Coaxial Stub Tuning, AEA Technology
    回復 支持 反對

    使用道具 舉報

  • TA的每日心情
    慵懶
    2013-12-29 10:03
  • 簽到天數: 64 天

    [LV.6]常住居民II

    發表於 2012-1-15 01:29:45 | 顯示全部樓層
    保爺........你欺負我這個台胞子喔!!!

    英文看不懂啦

    可不可以翻譯之後解釋的白話一點
    回復 支持 反對

    使用道具 舉報

  • TA的每日心情
    開心
    3 天前
  • 簽到天數: 1941 天

    [LV.Master]伴壇終老

    發表於 2012-1-15 02:15:26 | 顯示全部樓層
    阿鋒 發表於 2012-1-15 01:29
    保爺........你欺負我這個台胞子喔!!!

    英文看不懂啦

    有挑重點翻了.... 請細細品味!
    回復 支持 反對

    使用道具 舉報

  • TA的每日心情
    慵懶
    12 小時前
  • 簽到天數: 3725 天

    [LV.Master]伴壇終老

    發表於 2012-1-15 06:43:34 | 顯示全部樓層
    WSUgocouars 發表於 2012-1-15 01:25
    其實擁有天線分析儀的人真的就懂得怎麼用嗎?  我看很多都是懂非懂.... "我就是其中一個".... 自從搬了那 ...

    保哥說得是
    我也一直在研究那台
    該如何正確使用
    回復 支持 反對

    使用道具 舉報

    您需要登錄後才可以回帖 登錄 | 註冊

    本版積分規則

    小黑屋|手機版|Archiver|TRC 台灣無線電俱樂部 taiwan radio club  

    GMT+8, 2024-3-29 18:45 , Processed in 0.051875 second(s), 15 queries .

    Powered by Discuz! X3.3

    © 2001-2017 Comsenz Inc.

    快速回復 返回頂部 返回列表